Products

Just a few things we think you might need for your overlanding vehicle.


NEW: GFC/SP Camper Mod fridge cabinet/outdoor kitchen

Designed to hold an ARB Zero 47 fridge/freezer, this cabinet allows the fridge to be fully extended, or the outdoor kitchen to be fully extended, or the countertop extension to be fully extended, or all three extended at once. Comes in either 36” length (long bed) or 33” length (short bed). 36” tall.
- Industrial-grade aluminum extrusion framing with hidden connectors
- Fridge tray on 28" heavy duty lock-in/lock-out slides
- Outdoor kitchen on 34" (32" on short bed trucks) heavy duty lock-in/lock-out slides with cut-out for drop-in sink
- Collapsible drop-in sink with drain
- 3/4" bamboo counter extension on 30" heavy duty lock-in/lock-out slides
- 3/4" bamboo cutting board (20" x 28") for outdoor cooking at the tailgate (tung oil finish)
- Deep, full-extension drawer above fridge accessible from inside the camper (can be designed to open to the side)
- Marine-grade compression latch for drawer
- Storage cubbies behind the fridge (shallow single cubby for short bed trucks)
- Room to tuck a Mr. Heater Buddy behind the cabinet (long bed version only)
Price: $2,950

Order here

NEW: Alu-Cab Shadow awning mounting bracket for GFC RTT

The Shadow is a fantastic 270 awning. Unfortunately, mounting it to a GFC RTT requires a bracket at the rear pivot point that isn't provided by  Alu-Cab or GFC. This product solves the problem and eliminates the need for a third GFC universal mounting bracket.
- 12-gauge steel
- Works for both V1 and V2
- Slot for Shittco tent pole pass-through
- Mounting holes correspond to GFC extrusion T-slots and Alu-Cab Shadow mounting locations
- Slot to clear awning assembly bolts/nuts
- Uses standard GFC bolts, T-nuts, and “dogbones” for attaching to RTT
- Textured matte black powder coat finish
- GFC and awning mounting hardware not included
Price: $249

Order here

NEW: GFC lockable draw latch brackets

Everyone can use a little extra security…this allows you to lock your GFC RTT while still allowing the OEM pins to latch the RTT at the rear corners. Designed to work with the GFC T-nuts, bolts, and “dogbones”. The draw latch body is rubber and when paired with a rubber-guard padlock, should be quiet in the bumps. Get one set or add a second set for extra security.
- 12-gauge steel bracket set
- Weather-resistant, lockable draw latch with stainless-steel hardware
- Textured matte black powder coat finish
- Mounting hardware for latch
- Tamper-proof stainless-steel GFC mounting bolts
- GFC T-nuts and "dogbones" sold separately
Price: TBD until more orders come in

Order here

NEW: GFC/SP Roof Rail System 

A little beefier than the standard beef bars and with greater flexibility in terms of connection points, this system uses 45mm x 90mm extruded aluminum beams with six T-slots each (two top, two bottom, and one each side). The beam ends are sealed with silicone sealant and plastic end caps that separate the aluminum from the steel towers...then through-bolted to the towers with M8 screws. Can be ordered with or without 1/8” thick aluminum load stops.
- 53” wide between towers (XL available if needed)
- Clear anodized aluminum beam finish
- 12-gauge steel towers with matte black powder coat finish
- Includes M8 bolts and spring-loaded “positioning” nuts (four per beam) for attaching accessories
- Towers designed to work with GFC T-nuts, bolts and “dogbones”
- Optional 1/8” aluminum load stops with matte black powder coat finish and mounting hardware
- GFC mounting hardware sold separately
Price: $750 per two-beam set with four load stops, $450 per two-beam set without load stops

Order here

4Runner storage cabinet

The perfect solution if you need locking drawers and a sturdy work surface. This cabinet infills the lower portion of a 4Runner trunk.
- Solid birch dovetail drawers with 3/4" bamboo fronts
- Full-extension slides
- Locking marine compression latches
- 3/4" plywood or bamboo work table on full-extension slides
- Carpeted plywood top panel
- Secured with stainless turnbuckles (4)
Price: $2,100

Order here

Fridge/drawer cabinet

Designed specifically to hold the Engel MT45 dual-zone fridge/freezer. Bolts to the lower section of the dual-height 4WD-Mod.com Storage Plate System and fits behind the fully reclined rear seats of a 4-door rig.
- Fridge tray with full-extension, lock-in/lock-out 26" slides
- Solid birch, dovetail drawer with soft-close, full-extension slides
- 6" deep storage cubby behind the drawer
Email us for pricing.

Order here

Storage Plate System

We need a level secure floor for mounting gear and we think you might too. Our raised floor plate system  does all that plus adds storage under the plate. Need more storage? Opt for the single rear seat delete. Need even more? Opt for the double rear set delete. The plate is 15mm marine-grade plywood under 4mm waterproof vinyl plank flooring. Hatches are held securely in place with locking marine compression latches. Can be single or dual-height, trunk-only or trunk plus rear seat delete. 4-door or 2-door. Precise CNC-cut pieces throughout.
Email us for pricing.

Order here

Power Management Module (PMM)

PMM is a self-contained overlanding power management system for taking load off your vehicle's engine battery. Use it to power a fridge/freezer, lights, or even a blender...anything that requires AC or 12V DC. Our PMM includes the following:
- Victron 200Ah LiFePO4 battery
- Xantrex 2000 watt pure sine wave inverter/charger
- Renogy DC-DC charger and solar controller
- Victron smart battery monitor
- Xantrex Bluetooth remote panel
- AC duplex outlet
- USB/12V outlets
Email us for pricing.

Order here